i).The loop of thread stretch to form a perfect circular loop.; Surface tension pulls the thread along the length of the thread making the loop.;
ii).Surface tension;
sharon kalunda answered the question on August 6, 2019 at 07:54
-
In an experiment to determine the relative density of a substance using a density bottle the
following measurements were taken.
- Mass of empty density bottle =...
(Solved)
In an experiment to determine the relative density of a substance using a density bottle the
following measurements were taken.
- Mass of empty density bottle = 43.2 g
- Mass of bottle full of water = 66.4 g
- Mass of bottle filled with liquid X = 68.2g
Use the data to determine the density of the liquids.
Date posted:
August 6, 2019
.
Answers (1)
-
The figure below shows the path of ray of yellow light through a glass prism. The speed of
yellow light in the prism is 1.8 x...
(Solved)
The figure below shows the path of ray of yellow light through a glass prism. The speed of
yellow light in the prism is 1.8 x 108m/s.
(i) Determine the refractive index of the prism material (Speed of light in vacuum, C = 3.0 x 108m/s)
(ii) Show on the same diagram, the critical angle C and hence determine its value.
Date posted:
August 6, 2019
.
Answers (1)
-
The diagram below shows a narrow beam of white light onto a glass prism.
(i) What is the name of the phenomenon represented in the diagram?...
(Solved)
The diagram below shows a narrow beam of white light onto a glass prism.
(i) What is the name of the phenomenon represented in the diagram?
(ii) Name the color at X and Y
Date posted:
August 6, 2019
.
Answers (1)
-
A 5µF capacitor is charged to a potential difference of 200V and isolated. It is then connected
to a 10µF capacitor.Find
(i) The resultant potential difference across...
(Solved)
A 5μF capacitor is charged to a potential difference of 200V and isolated. It is then connected
to a 10μF capacitor.Find
(i) The resultant potential difference across the combination
(ii) Energy stored before connection
(iii) Total energy in the capacitors after connection
Date posted:
August 6, 2019
.
Answers (1)
-
The figure shows a human eye with a defect
(i) Identify the defect
(ii) Explain how the defect could be corrected
(iii) Draw a suitable diagram...
(Solved)
The figure shows a human eye with a defect
(i) Identify the defect
(ii) Explain how the defect could be corrected
(iii) Draw a suitable diagram to show the correction of the defect
Date posted:
August 6, 2019
.
Answers (1)
-
When the switch S is kept open in the circuit shown below the voltmeter reads 1.5V. When the switch is closed, the readings drops to...
(Solved)
When the switch S is kept open in the circuit shown below the voltmeter reads 1.5V. When the switch is closed, the readings drops to 1.3V and the current through the resistor is 0.5A.
(i) What is the e.m.f of the cell?
(ii) What the terminal voltage of the cell?
(iii) Calculate the value of R.
Date posted:
August 6, 2019
.
Answers (1)
-
The figure below shows how a student set up a circuit using 3 identical bulbs X, Y and Z
each rated “12V, 2.0A”
(i) When operating normally,...
(Solved)
The figure below shows how a student set up a circuit using 3 identical bulbs X, Y and Z
each rated “12V, 2.0A”
(i) When operating normally, calculate the resistance of one of the bulbs.
(ii) Calculate the effective resistance of the three bulbs.
(iii) What will be reading of the ammeter?
(iv) Draw a circuit diagram showing the three bulbs connected in such a way that they would all work at the same brightness especially if they are not identical.
Date posted:
August 6, 2019
.
Answers (1)
-
State two quantities that are used to determine whether accumulator require recharging or not.
(Solved)
State two quantities that are used to determine whether accumulator require recharging or not.
Date posted:
August 6, 2019
.
Answers (1)
-
State one advantage of using an optical fibre in communication.
(Solved)
State one advantage of using an optical fibre in communication.
Date posted:
August 6, 2019
.
Answers (1)
-
The figure below shows how the displacement varies for a certain wave.
Determine the frequency of the wave.
(Solved)
The figure below shows how the displacement varies for a certain wave.
Determine the frequency of the wave.
Date posted:
August 6, 2019
.
Answers (1)
-
Explain why soft iron keepers are suitable for storing magnets.
(Solved)
Explain why soft iron keepers are suitable for storing magnets.
Date posted:
August 6, 2019
.
Answers (1)
-
The figure below shows a ray of light incident on a plane mirror.
(Solved)
The figure below shows a ray of light incident on a plane mirror.
The plane mirror is then rotated clockwise through an angle of 200 keeping the incident ray
fixed. Determine the new angle of reflection.
Date posted:
August 6, 2019
.
Answers (1)
-
Explain why it is easier to loosen a tight nut using a spanner with long handle
(Solved)
Explain why it is easier to loosen a tight nut using a spanner with long handle
Date posted:
June 8, 2019
.
Answers (1)
-
State four significance of Karst regions.
(Solved)
State four significance of Karst regions.
Date posted:
June 4, 2019
.
Answers (1)
-
The figure below shows a pipe of varying cross-section. Three vertical tubes X, Y and Z of same diameter are fixed to the section A,...
(Solved)
The figure below shows a pipe of varying cross-section. Three vertical tubes X, Y and Z of same diameter are fixed to the section A, B and C of the pipe respectively as shown below.
Given that the water flows in the direction shown by the arrow, indicate on the diagram the relative levels of water in Y and Z.
Date posted:
June 4, 2019
.
Answers (1)
-
The densities of liquids may be measured using hydrometers. The
hydrometer in the Figure below consists of a weighted bulb with a thin stem , and...
(Solved)
The densities of liquids may be measured using hydrometers. The
hydrometer in the Figure below consists of a weighted bulb with a thin stem , and is floating to the depth shown when it is immersed in a liquid whose density is 0.8g/cm3.
The hydrometer has a mass of 165g and the stem has a uniform cross-sectional area of 0.75 cm2. Calculate;
I. the change in the submerged volume of the hydrometer when it is first placed in a liquid of density 1.00 g/cm3 and then in the liquid of density 1.25 g/cm3.
II. the distance on the stem between the 1.0 g/cm3 and 1.25 g/cm3 graduations.
Date posted:
June 4, 2019
.
Answers (1)
-
A bullet of mass 2g is fired horizontally into a block of wood of mass
498g. The block is suspended by a light inextensible string so...
(Solved)
A bullet of mass 2g is fired horizontally into a block of wood of mass
498g. The block is suspended by a light inextensible string so that it is able to move in a vertical plane. The block and the bullet move together through a vertical distance of 8.6cm as shown in figure below.
I. Calculate the change in gravitational potential energy of the block and bullet.
II. Calculate the initial velocity of the block and bullet after they start moving together.
III. Determine the speed of the bullet before the impact with the block.
Date posted:
June 4, 2019
.
Answers (1)
-
State the SI unit of momentum as used in Physics.
(Solved)
State the SI unit of momentum as used in Physics.
Date posted:
June 4, 2019
.
Answers (1)
-
The Figure below shows a velocity-time graph for a steel ball falling
through a viscous fluid.
Explain the nature of the curve in;
(i) section PQ.
(ii) section QR.
(iii)...
(Solved)
The Figure below shows a velocity-time graph for a steel ball falling
through a viscous fluid.
Explain the nature of the curve in;
(i) section PQ.
(ii) section QR.
(iii) If the graph shown above is of a ball falling through water, sketch on the same axis a graph for the ball falling through glycerine.
Date posted:
June 4, 2019
.
Answers (1)
-
The Figure 11 below shows a hydraulic lift supporting a load of 150kg. Its cross-sectional areas A1 and A2 are 0.02m2 and 0.4m2 respectively. The...
(Solved)
The Figure 11 below shows a hydraulic lift supporting a load of 150kg. Its cross-sectional areas A1 and A2 are 0.02m2 and 0.4m2 respectively. The length of the effort arm is 1m and the length of the plunger from the pivot is 0.4m.
Determine:
(i) the pressure exerted by 150kg mass.
(ii) the pressure exerted by F1 on the smaller piston.
(iii) the force F1.
(iv) the applied force, Fe.
(v) the mechanical advantage.
(vi) the velocity ratio of the system.
(v) the efficiency of the system.
Date posted:
June 4, 2019
.
Answers (1)