Ccna 601-802: Cisco Certified Network Associate Question Paper

Ccna 601-802: Cisco Certified Network Associate

Course:Cisco

Institution: Kenya Highlands University question papers

Exam Year:2010

Kenya highlands University
CISCO Certified Network Associate
Exam 601-802-Composite
March 2010
Answer all questions
1. What is the sys-id-ext field in a BPDU used for?
A. It is a 4-bit field inserted into an Ethernet frame to define trunking information
between switches.
B. It is a 12-bit field inserted into an Ethernet frame to define VLANs in an STP
instance.
C. It is a 4-bit field inserted into an non-Ethernet frame to define EtherChannel
options.
D. It is a 12-bit field inserted into an Ethernet frame to define STP root bridges.
2. You have four RSTP PVST+ links between switches and want to aggregate the bandwidth.
What solution will you use?
A. EtherChannel
B. PortFast
C. BPDU Channel
D. VLANs
E. EtherBundle
3. What configuration parameters must be configured the same between switches for
LACP to form a channel? (Choose three.)
A. Virtual MAC address
B. Port speeds
C. Duplex
D. PortFast enabled
E. Allowed VLAN information
4. You reload a router with a configuration register setting of 0x2101. What will the
router do when it reloads?
A. The router enters setup mode.
B. The router enters ROM monitor mode.
C. The router boots the mini-IOS in ROM.
D. The router expands the first IOS in flash memory into RAM.
5. Which of the following commands provides the product ID and serial number of a router?
A. show license
B. show license feature
C. show version
D. show license udi
6. Which command allows you to view the technology options and licenses that are supported
on your router along with several status variables?
A. show license
B. show license feature
C. show license udi
D. show version
7. Which of the following will you use to collect details about network traffic patterns on
your network, including protocols used.
A. SNMPv3
B. Syslogv2
C. NetFlow 9
D. logging host ip_address
8. You want to send a console message to a syslog server, but you only want to send status
messages of 3 and lower. Which of the following commands will you use?
A. logging trap emergencies
B. logging trap errors
C. logging trap debugging
D. logging trap notifications
E. logging trap critical
F. logging trap warnings
G. logging trap alerts
9. When is the AVR router used in GLBP?
A. When HSRP preempts GLBP
B. When a client needs the virtual MAC
C. When it’s set to passive mode and load balancing
D. When it’s load-balancing between VLANs with VVRP
E. When there is a redundancy failure
You need to connect to a remote IPv6 server in your virtual server farm. You can connect
to the IPv4 servers, but not the critical IPv6 server you desperately need. Based on
the following output, what could your problem be?
C:\>ipconfig
Connection-specific DNS Suffix . : localdomain
IPv6 Address. . . . . . . . . . . : 2001:db8:3c4d:3:ac3b:2ef:1823:8938
Temporary IPv6 Address. . . . . . : 2001:db8:3c4d:3:2f33:44dd:211:1c3d
Link-local IPv6 Address . . . . . : fe80::ac3b:2ef:1823:8938%11
IPv4 Address. . . . . . . . . . . : 10.1.1.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 10.1.1.1
A. The global address is in the wrong subnet.
B. The IPv6 default gateway has not been configured or received from the router.
C. The link-local address has not been resolved so the host cannot communicate to
the router.
D. There are two IPv6 global addresses configured. One must be removed from the
configuration.
11. What command is used to view the IPv6-to-MAC-address resolution table on a
Cisco router?
A. show ip arp
B. show ipv6 arp
C. show ip neighbors
D. show ipv6 neighbors
E. show arp
12. An IPv6 ARP entry is listed as with a status of REACH. What can you conclude about
the IPv6-to-MAC-address mapping?
A. The interface has communicated with the neighbor address and the mapping is
current.
B. The interface has not communicated within the neighbor reachable time frame.
C. The ARP entry has timed out.
D. IPv6 can reach the neighbor address but the addresses has not yet been resolved.
Serial0/1 goes down. How will EIGRP send packets to the 10.1.1.0 network?
Corp#show ip eigrp topology
[output cut]
P 10.1.1.0/24, 2 successors, FD is 2681842
via 10.1.2.2 (2681842/2169856), Serial0/0
via 10.1.3.1 (2973467/2579243), Serial0/2
via 10.1.3.3 (2681842/2169856), Serial0/1
A. EIGRP will put the 10.1.1.0 network into active mode.
B. EIGRP will drop all packets destined for 10.1.1.0.
C. EIGRP will just keep sending packets out s0/0.
E. EIGRP will use s0/2 as the successor and keep routing to 10.1.1.0.
14. What command produced the following output?
via FE80::201:C9FF:FED0:3301 (29110112/33316), Serial0/0/0
via FE80::209:7CFF:FE51:B401 (4470112/42216), Serial0/0/1
via FE80::209:7CFF:FE51:B401 (2170112/2816), Serial0/0/2
A. show ip protocols
B. show ipv6 protocols
C. show ip eigrp neighbors
D. show ipv6 eigrp neighbors
E. show ip eigrp topology
F. show ipv6 eigrp topology
15. You need to troubleshoot an adjacency between two EIGRP configured routers? What
should you look for? (Choose four.)
A. Verify the AS numbers.
B. Verify that you have the proper interfaces enabled for EIGRP.
C. Make sure there are no mismatched K-values.
D. Check your passive interface settings.
E. Make sure your remote routers are not connected to the Internet.
F. If authentication is configured, make sure all routers use different passwords.
How should a router that is being used in a frame relay network be configured to keep
split horizon issues from preventing routing updates?
A. Configure a single subinterface to establish multiple PVC connections to multiple
remote router interfaces.
B. Combine multiple frame relay circuits as a point-to-point line to support multicast
and broadcast traffic.
C. Configure many subinterfaces in the same subnet.
D. Configure a separate subinterface for each PVC with a unique DLCI and subnet
assigned to the subinterface.
22. IPv6 unicast routing is running on the Corp router. Which of the following addresses
would show up with the show ipv6 int brief command?
Corp#sh int f0/0
FastEthernet0/0 is up, line protocol is up
Hardware is AmdFE, address is 000d.bd3b.0d80 (bia 000d.bd3b.0d80)
[output cut]
A. FF02::3c3d:0d:bdff:fe3b:0d80
B. FE80::3c3d:2d:bdff:fe3b:0d80
C. FE80::3c3d:0d:bdff:fe3b:0d80
D. FE80::3c3d:2d:ffbd:3bfe:0d80
23. A host sends a type of NDP message providing the MAC address that was requested.
Which type of NDP was sent?
A. NA
B. RS
C. RA
D. NS
24. Each field in an IPv6 address is how many bits long?
A. 4
B. 16
C. 32
D. 128
To enable OSPFv3, which of the following would you use?
A. Router(config-if)#ipv6 ospf 10 area 0.0.0.0
B. Router(config-if)#ipv6 router rip 1
C. Router(config)#ipv6 router eigrp 10
D. Router(config-rtr)#no shutdown
E. Router(config-if)#ospf ipv6 10 area 0
26. What does the command routerA(config)#line cons 0 allow you to perform next?
A. Set the Telnet password.
B. Shut down the router.
C. Set your console password.
D. Disable console connections.
27. Which two statements describe the IP address 10.16.3.65/23? (Choose two.)
A. The subnet address is 10.16.3.0 255.255.254.0.
B. The lowest host address in the subnet is 10.16.2.1 255.255.254.0.
C. The last valid host address in the subnet is 10.16.2.254 255.255.254.0.
D. The broadcast address of the subnet is 10.16.3.255 255.255.254.0.
E. The network is not subnetted.
28. On which interface do you configure an IP address for a switch?
A. int fa0/0
B. int vty 0 15
C. int vlan 1
D. int s/0/0
29. Which of the following is the valid host range for the subnet on which the IP address
192.168.168.188 255.255.255.192 resides?
A. 192.168.168.129–190
B. 192.168.168.129–191
C. 192.168.168.128–190
D. 192.168.168.128–192
30. Which of the following is considered to be the inside host’s address after translation?
A. Inside local
B. Outside local
C. Inside global
D. Outside global
Your inside locals are not being translated to the inside global addresses. Which of the following
commands will show you if your inside globals are allowed to use the NAT pool?
ip nat pool Corp 198.18.41.129 198.18.41.134 netmask 255.255.255.248
ip nat inside source list 100 int pool Corp overload
A. debug ip nat
B. show access-list
C. show ip nat translation
D. show ip nat statistics
32. How many collision domains are created when you segment a network with a
12-port switch?
A. 1
B. 2
C. 5
D. 12
33. Which of the following commands will allow you to set your Telnet password on a
Cisco router?
A. line telnet 0 4
B. line aux 0 4
C. line vty 0 4
D. line con 0
34. Which router command allows you to view the entire contents of all access lists?
A. show all access-lists
B. show access-lists
C. show ip interface
D. show interface
35. What does a VLAN do?
A. Acts as the fastest port to all servers
B. Provides multiple collision domains on one switch port
C. Breaks up broadcast domains in a layer 2 switch internetwork
D. Provides multiple broadcast domains within a single collision domain
If you wanted to delete the configuration stored in NVRAM, choose the best answer
for the Cisco objectives.
A. erase startup
B. delete running
C. erase flash
D. erase running
37. Which protocol is used to send a destination network unknown message back to originating
hosts?
A. TCP
B. ARP
C. ICMP
D. BootP
38. Which class of IP address provides 15 bits for subnetting?
A. A
B. B
C. C
D. D
39. There are three possible routes for a router to reach a destination network. The first
route is from OSPF with a metric of 782. The second route is from RIPv2 with a metric
of 4. The third is from EIGRP with a composite metric of 20514560. Which route will
be installed by the router in its routing table?
A. RIPv2
B. EIGRP
C. OSPF
D. All three
40. Which one of the following is true regarding VLANs?
A. Two VLANs are configured by default on all Cisco switches.
B. VLANs only work if you have a complete Cisco switched internetwork. No offbrand
switches are allowed.
C. You should not have more than 10 switches in the same VTP domain.
D. You need to have a trunk link configured between switches in order to send information
about more than one VLAN down the link.
Which two of the following commands will place network 10.2.3.0/24 into area 0?
(Choose two.)
A. router eigrp 10
B. router ospf 10
C. router rip
D. network 10.0.0.0
E. network 10.2.3.0 255.255.255.0 area 0
F. network 10.2.3.0 0.0.0.255 area0
G. network 10.2.3.0 0.0.0.255 area 0
42. How many broadcast domains are created when you segment a network with a
12-port switch?
A. 1
B. 2
C. 5
D. 12
43. If routers in a single area are configured with the same priority value, what value does
a router use for the OSPF router ID in the absence of a loopback interface?
A. The lowest IP address of any physical interface
B. The highest IP address of any physical interface
C. The lowest IP address of any logical interface
D. The highest IP address of any logical interface
44. What protocols are used to configure trunking on a switch? (Choose two.)
A. VLAN Trunking Protocol
B. VLAN
C. 802.1q
D. ISL
45. What is a stub network?
A. A network with more than one exit point
B. A network with more than one exit and entry point
C. A network with only one entry and no exit point
D. A network that has only one entry and exit point

📘 Access 10,000+ CBC Exams With Marking Schemes

Ccna 601-802: Cisco Certified Network Associate Question Paper

More Question Papers

Exams With Marking Schemes

End Term 3 Exams

Mid Term Exams

End Term 1 Exams

Opener Exams

Full Set Exams